Diy paper skyscraper11/21/2023 ![]() I will concentrate on the box above which when complete will form a rectangle. You will need to measure both the long sides and the short sides and transfer these measurements to the tops or bottoms. Using your set square transfer the measurements to a piece of card and draw the shape that you need. To do this you will first need to measure the four sides of the open end of the box that you are working on. This will ensure that the boxes stay in shape and also provide a good surface for you to stick to or decorate with a design. The next thing to do is to make the tops, bottoms and sides for each of the boxes. Remember always ask an adult for help when using scissors or craft knives. Take some scissors or a craft knife and carefully cut around the lines you have marked out making sure that you do not cut off the existing joining tab that was holding the box together. When you have done this all around the box you are ready to cut out the tabs. Once this is done use the ruler to measure up 1cm from the fold line at each end of the tab and join your two points together. Then draw a line at 45 degrees as shown below. ![]() Start by placing your set square on the fold line that is already on the card. To mark out your tabs you will need to use your set square and ruler. ( see Tops bottoms and sides below.)īy doing this you will be able to provide a clean flat surface to join your boxes together or a flat side for you to paint and add your detail on your model Skyscraper. These will be used for fixing your top and bottom pieces or side pieces depending on how you position the box. Mark out your tabs on the card that formed the ends of your boxes as shown below. ![]() Once you have reversed the boxes lay them flat and mark out tabs on each end. I have chosen five boxes of various sizes and a kitchen roll insert. If you do damage the box slightly don't worry as you can always cover the damage with a piece of plain paper or card should you wish too. You could try lightly dabbing the join with a warm damp cloth but in most cases, I have found this method to be unsuccessful as the card becomes too soft to separate properly and tends to tear more easily. Hint: Use the edge of a ruler or blunt dinner knife to help separate the edges. You should be able to see a long tab inside the box that joins the sides together.Ĭarefully separate the join trying not to rip the box as you do so. The next thing to do is to look inside the box and find where the box is joined together. When these are open it enables you to flatten the box out. These are the ends that are used to open the box. To disassemble a cardboard box you will first need to open the two factory ends of the box so as to enable you to flatten the box. By reversing the box you will have a clean matte surface that makes them easy to colour and prevents the colour from coming off in most cases. This results in the colour's rubbing off when the models dry. This is because they have a shiny or smooth glossy finish that does not accept paint or other colour mediums such as crayons, markers or coloured pencils very well. Taking them apart is optional but I have found that some types of packaging are very hard to paint. Once you have decided which boxes you are going to use you will first need to take them apart. Hint: Try placing different types of boxes on top of each other first to see how the Skyscraper might look. ![]() There are so many different types of cardboard boxes and they come in all shapes and sizes, such as cereal boxes, cookies, chips, and everyday food items so the possibilities for the skyscraper are limitless. To make Skythescraper you will first need to gather a collection of cardboard boxes. Glue spreader or glue stick Constructing the Skyscraper. Parental supervision required !!.Ĭrayons ( or coloured pencils or pastels or paints) NB: You will be using scissors or a craft knife so it may require adult supervision. There's a lot of marking out and cutting out to do, which is quite complicated and may take a little time. It is made using ordinary cardboard boxes of various shapes and sizes so it can be constructed any way you like and would be ideal for any Ks2 - Ks3 school art project, or for you to make an imaginary city by making several of them. It is simple to make and does not necessarily have to look like the one in the example. ![]() In this craft project, you will be making a skyscraper. How to build a cardboard model Skyscraper. ![]()
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |